u乐国际平台注册软件平台
Nominal Load / Rated load
Sensitivity
Excitation Voltage
Safe-overload
Ultimate overload
Non-linearity
Creep
Temperature-effect-@zero-load
 
Temperature-effect-on-sensitivity
Zero-balance/No-load-output
Zero-return
Non-repeatability
Hysteresis
Resistance-measurements
IP Protection
 
u乐国际平台注册注册登录
The nominal load means the upper limit of the measuring range of a loadcell or transducer. Load can be tensile or compressive force. Indicated in units of mass or force according to the calibration.
 
u乐国际平台注册地址首页
This is the maximum signal output at the rated load of the Load cell expressed in millivolt per volt (mV/V). This is also termed as rated output or full scale output(FSO)
 
u乐国际平台注册官网注册
The excitation voltage is the input voltage, in which the load cell can be operated in practical applications and within which the technical data and error specifications are maintained.(Usually 10 VDC- maximum 15VDC)
 
u乐国际平台注册首页客户端
The maximum load that can be applied without producing a permanent shift in the performance characteristics beyond specifications.Generally 150% of the rated load.
 
u乐国际平台注册安卓软件
The load at which the spring element takes permanent deformation.Generally 200% of rated load.
 
u乐国际平台注册安卓软件
The maximum deviation of the actual calibration curve from the ideal curve between zero and rated load outputs.
Measured on increasing load only.
Expressed as a percentage of the rated output.
 
u乐国际平台注册平台在线
Under constant load the change in load cell output that occurs with time.Its always increases with increasing load and temperature.
 
u乐国际平台注册官网注册
The change in zero balance due to the change in ambient temperature.
 
u乐国际平台注册二维码安卓
The change in output at loaded condition due to the change in ambient temperature
 
u乐国际平台注册平台在线
The signal output of the load cell with rated excitation and with no load applied.
Usually expressed as a percentage of full scale output or rated output.
 
u乐国际平台注册安卓软件
The difference in zero balance measured immediately before rated load application of specified duration and measured after removal of the load and when the output has stabilised.
 
u乐国际平台注册网站ios
The maximum difference between load cell output reading for repeated loading under identical loading condition/ pattern and environmental conditions
Expressed as a percentage of rated output

 
u乐国际平台注册软件平台
The maximum difference between load cell output reading for the same applied load, one reading obtained by increasing load from zero and the other by decreasing the load from rated load Expressed as a percentage of rated output.
 
u乐国际平台注册网站客户端
Input resistance
Output resistance
   
u乐国际平台注册网址注册 Insulation resistance between body and conductor
u乐国际平台注册地址下载 Insulation resistance between body and shield
u乐国际平台注册官网注册 Insulation resistance between conductor and shield
 
u乐国际平台注册平台官网
u乐国际平台注册网站ios
 
u乐国际平台注册网站ios u乐国际平台注册地址下载 u乐国际平台注册二维码安卓 u乐国际平台注册平台在线
0 Not Protected 0 Not Protected
1 Protected against solid object > 50mm 1 Protected against Dripping Water
2 Protected against solid object > 12mm 2 Protected against Dripping Water when tilted upto 15 Deg
3 Protected against solid object > 2.5mm 3 Protected against spraying Water
4 Protected against solid object > 1mm 4 Protected against splashing Water
5 Dust Protected 5 Protected against Water Jets
6 Dust Tight 6 Protected against Heavy Seas
7 NA 7 Protected against the effects of immersion
8 NA 8 Protected against submersion